網帶式超聲波噴淋清洗機，通過式超聲波噴淋清洗烘干線應用廣泛，很多人不知道他的工作流程，網帶式超聲波噴淋清洗機有效去油，除蠟，除銹，除污。有清洗、漂洗、干燥等功能。
The mesh belt ultrasonic spray cleaning machine and the pass through ultrasonic spray cleaning and drying line are widely used. Many people do not know its working process. The mesh belt ultrasonic spray cleaning machine can effectively remove oil, wax, rust and dirt. It has the functions of cleaning, rinsing and drying.
網帶式超聲波噴淋清洗機工藝流程：投料→ 超聲波去污（28KHZ）→ 超聲波清洗（40K）→ 清水或純水（鼓泡）→ 風吹→ 下料
Process flow of mesh belt ultrasonic spray washer: feeding → ultrasonic decontamination (28KHZ) → ultrasonic cleaning (40K) → clean water or pure water (bubbling) → air blowing → blanking
網帶式超聲波噴淋清洗機由超聲波清洗系統、箱體室、罐體加熱系統、輸送鏈及傳動系統、壓縮空氣干燥系統、油水分離器、自動刮油機、電氣控制系統等組成.
The mesh belt ultrasonic spray washer is composed of ultrasonic cleaning system, box chamber, tank heating system, conveyor chain and transmission system, compressed air drying system, oil-water separator, automatic oil scraper, electrical control system, etc
網帶式超聲波噴淋清洗機為鏈條網帶通超型超聲波清洗漂洗機。采用專用鏈條傳動輸送工件，具有清洗、漂洗、吹水等功能。將工件手動放置在傳動鏈的網帶上，然后通過通超聲波清洗室、超聲波清洗室、鼓泡清洗室和噴水室。
The mesh belt ultrasonic spray washer is a chain mesh belt pass ultrasonic cleaning and rinsing machine. The special chain drive is used to transport the workpiece, which has the functions of cleaning, rinsing, water blowing, etc. Place the workpiece manually on the mesh belt of the drive chain, and then pass through the ultrasonic cleaning room, ultrasonic cleaning room, bubble cleaning room and water spray room.

清洗、漂洗、干燥等工序完成后，物料排出。
After the cleaning, rinsing, drying and other processes are completed, the materials are discharged.
清洗液經凈化處理后可循環使用，上罩內的水霧經抽風機抽出后排放主排氣管。該機具有多工位、功能齊全、結構合理、操作方便、清洗效果好等優點，對流水線零件的清洗、改善工作環境、提高清洗干燥質量具有重要意義。
The cleaning solution can be recycled after purification treatment. The water mist in the upper cover is pumped out by the exhaust fan and then discharged to the main exhaust pipe. This machine has the advantages of multi station, complete functions, reasonable structure, convenient operation, good cleaning effect, etc. It is of great significance to clean the parts of the convection waterline, improve the working environment, and improve the quality of cleaning and drying.
網帶采用專用不銹鋼網帶。由于工件較重，采用三鏈形式，保證每平方分米軸承壓力不低于20kg。工件用專用夾具固定在網帶上，保證無滑動、無接觸、易清潔.
The mesh belt adopts special stainless steel mesh belt. As the workpiece is heavy, the form of three chains is adopted to ensure that the bearing pressure per square decimeter is not less than 20kg. The workpiece is fixed on the mesh belt with a special fixture to ensure no sliding, no contact and easy cleaning
調速面板配有：轉速表、電源開關、指示燈、保險絲、表盤、調速旋鈕。使用時應先啟動輸送電機；然后將速度控制器電源開關置于“on（通）”位置，指示燈亮；輕輕轉動調速旋鈕，即可改變調速電機的轉速：順時針?lè)较蜣D(zhuǎn)速升高，逆時針?lè)较蜣D(zhuǎn)速降低；然后按下轉速表以穩定所需的速度。停機時，先將調速控制器電源開關置于“off”位置；2-3分鐘后關閉輸送電機.
The speed control panel is equipped with: tachometer, power switch, indicator light, fuse, dial and speed control knob. When using, start the conveying motor first; Then turn the power switch of speed controller to the "on" position, and the indicator light will be on; Gently turn the speed regulating knob to change the speed of the speed regulating motor: the speed increases in the clockwise direction and decreases in the counterclockwise direction; Then press the tachometer to stabilize the desired speed. When shutting down, first set the power switch of the speed control controller to the "off" position; Turn off the conveying motor after 2-3 minutes