Many people are still very unfamiliar with the ultrasonic cleaning machine. Now the ultrasonic cleaning machine is widely used in our life, so many people want to learn the operation process of the ultrasonic cleaning machine. Today, Xiaobian will briefly introduce the cleaning process and operation steps of the ultrasonic cleaning machine.

清洗工藝流程：上料-超聲清洗（清洗劑）-超聲漂洗（水）-風槍吹水-熱風烘干-涂層。

Cleaning process: feeding - ultrasonic cleaning (cleaning agent) - ultrasonic rinsing (water) - air gun blowing - hot air drying - coating.

操作步驟如下：

The operation steps are as follows:

1、準備：在清洗槽內加入清洗液，要求達到預定水位（容積2/3）。打開電源，電源指示燈亮，數控區面板亮，此時儀器處于待機狀態。

1. Preparation: add cleaning fluid into the cleaning tank and it is required to reach the predetermined water level (Volume 2 / 3). When the power is turned on, the power indicator light is on, and the panel of the NC area is on. At this time, the instrument is in standby mode.

2、不需要清洗計時：按動超聲鍵，超聲指示燈長亮，開始超聲清洗，超聲功率數碼管顯示當前超聲功率值。再次按動超聲鍵，超聲清洗結束。

2. Cleaning timing is not required: press the ultrasonic key, the ultrasonic indicator light will be on for a long time, start ultrasonic cleaning, and the ultrasonic power nixie tube will display the current ultrasonic power value. Press the ultrasonic key again to finish the ultrasonic cleaning.

3、需要清洗計時：按動計時鍵，計時指示燈閃爍，開始超聲清洗，清洗時間數碼管顯示設定時間值。按動超聲鍵，超聲指示燈長亮，開始超聲清洗，超聲功率數碼管顯示當前超聲功率值。時間指示燈長亮，同時清洗時間值以1分鐘為單位遞減。當清洗時間遞減為0,蜂鳴器報警，表示清洗結束。

3. Cleaning timing required: press the timing key, the timing indicator flashes, start ultrasonic cleaning, and the cleaning time nixie tube displays the set time value. Press the ultrasonic key, the ultrasonic indicator light will be on for a long time to start ultrasonic cleaning, and the ultrasonic power nixie tube will display the current ultrasonic power value. The time indicator is on for a long time, and the cleaning time value decreases in 1 minute. When the cleaning time decreases to 0, the buzzer alarms, indicating that the cleaning is over.

4、需要加熱時：使用加熱功能清洗槽液位容積必 須達到容積2/3處，然后按動加熱鍵，設定加熱溫度，加熱溫度指示燈閃爍，加熱數碼管顯示當前水槽溫度，加熱數碼管顯示值隨著水槽的溫度升高變化。（當前水槽溫度達到設定溫度值時則自動停止加熱）。

4. When heating is required: the liquid level volume of the cleaning tank must reach 2 / 3 of the volume by using the heating function, then press the heating key to set the heating temperature, the heating temperature indicator flashes, the heating nixie tube displays the current tank temperature, and the display value of the heating nixie tube changes with the increase of the tank temperature（ When the current water tank temperature reaches the set temperature value, the heating will be stopped automatically).

5、功率調節：按超聲區域的"∧"鍵，超聲功率數碼管顯示為上一次設定值增加10%,按超聲區域的"∨"鍵，超 聲 波 功率數碼管顯示為上一次設定減少10%.超聲功率設定范圍為40%-,即為此機的功率300W.

5. Power adjustment: press the "∧" key in the ultrasonic area, and the ultrasonic power nixie tube will display that the last set value increases by 10%. Press the "∨" key in the ultrasonic area, and the ultrasonic power nixie tube will display that the last set value decreases by 10%. The ultrasonic power setting range is 40% - , , that is, the power of this machine is 300W

6、啟動各功能鍵（電源鍵、加熱鍵、計時鍵和超聲鍵）時，應按動功能鍵時間不少于3秒，然后松開，各功能鍵按鍵間隔時間不能小于3秒。

6. When starting each function key (power key, heating key, timing key and ultrasonic key), press the function key for not less than 3 seconds, and then release it. The key interval of each function key shall not be less than 3 seconds.

利用超 聲 波 清洗機對工件進行清洗或加工的行業愈來愈多，這是由于它有眾多優點。因此，品質有保證的超 聲 波 清洗機也受到了人們的歡迎。

More and more industries use ultrasonic cleaning machine to clean or process workpieces, because it has many advantages. Therefore, the ultrasonic cleaning machine with guaranteed quality has also been welcomed by people.